MAGNETEK GPD 515 PDF

The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.

Author: Mumi Mooguktilar
Country: Russian Federation
Language: English (Spanish)
Genre: Music
Published (Last): 23 September 2017
Pages: 168
PDF File Size: 15.82 Mb
ePub File Size: 2.85 Mb
ISBN: 517-2-98198-206-6
Downloads: 11153
Price: Free* [*Free Regsitration Required]
Uploader: Fegore

The corresponding action the drive will take is dependent upon the setting of L 8 – 0 3 see below.

When the motor has the same capacity as that of the drive, the gain is 1. When o 2 – 0 3 is not set to ” 1 “, this option is not available. One of two methods may be used to run the drive in torque control.

Hunt Prevent Selection Factory setting: A E E E E 0. Each is set, in increments of 0. This allows all parameters to be viewed and modified. Learn More – opens in a new window or tab International shipping and import charges paid to Pitney Bowes Inc.

Verify that the rated voltage of the drive matches the voltage of the incoming power. Disconnect the two scope channels, and reconnect them to terminals 6 and 7 of TA1. When using magnehek open collector input, use transistors with rated voltage of 35 Vdc or more and rated current of mA or more. During acceleration, if the output current exceeds the value in Pgd 3 – 0 2acceleration stops and frequency is maintained.

Output Frequency B Mid. When there is a long time lag between the applying of control power and actual run operation, output voltage may be produced due to the integrator offset. The following tables list all parameters in numerical order. MRO Electric provided excellent service to us when we needed it most. Setting b to ” 0 ” may correct a runaway condition.

  JOOP KLEPZEIKER PDF

This is achieved by dissipating the regenerative energy of the AC motor across the resistive components of the Dynamic Braking option. MRO is committed to customer satisfaction!

Yaskawa / MagneTek / Saftronics / Omron Magnetek G5 GPD 515 Drives

Fuse blown DC fuse has cleared. Digital Operator Table When C 3 – 0 5 is set to 0, the motor will enter the constant horsepower range when motor speed exceeds motor rated synchronous speed.

Call for an accurate magnetsk. Learn More – opens in a new window or tab Any international shipping and import charges are paid in part to Pitney Bowes Inc. This parameter must be set to ” 0 ” for Drive mode operation.

Stall Prevention Level During Running This parameter determines the actual drive output current level while operating at set speed frequency.

No part of this document may be stored in a retrieval system, or transmitted, in any form More information. Display the operating hours when the last fault occurred.

This causes a ” LF ” fault to occur and the motor to coast to a stop. Detected during running, and operation continues after detection 3: Multi-function Analog Input 1 Selection Term. The User Program Access Level will only be available if one or more parameters are programmed into A 2 – 0 1 through A 2 – 3 2. Speed Limit Factory setting: You will find PES meets all these requirements and more!

Enable operation continues 1: See Note 1 REF. Would recommend them to anyone. Any damages or shortages evident when the equipment is received must be reported immediately to the commercial carrier who transported the equipment.

Trim Control Increase Data 1 D: Make sure you know which polarity you have on your VOM. Be sure to observe the following: This speed limit can come from either a programmed value d 5 – 0 4or an analog input Term. Rampt to Stop Error E 1: Operation Selection at Overspeed Factory setting: This parameter setting determines the factory settings for the parameters listed in the table below.

  CARAZAMBA DE VIRGILIO RODRIGUEZ MACAL PDF

Miscellaneous – Misc. Equipment

Program all parameter settings with the data that was recorded in step 1. After that length of time the drive continues to decelerate until the output frequency is zero. By monitoring DC bus voltage, the deceleration rate is automatically adjusted so that deceleration can be completed in the shortest amount of time, magntek of the set deceleration time.

Speed pot or VDC signal only: Want it shipped today? Connect output conduit armored cable or shielded cable in a manner that allows it to act as an unbroken shield from the drive panel to the motor casing. The deviation detection level is an adjustable value, which can be set in parameter F 1 – 1 0. Display unit differs depending on setting of o 1 – 0 3.

Yaskawa GPD /g5 Model Cimr-g5m25p5 Gpdc-a 25p51f MAGNETEK G5 | eBay

They provided me with a quality piece of equipment that allowed me g;d get my paint booth exhaust fan back up and running for a minimal cost, and the shipping was extremely quick as well.

For Classroom Use Only! If the scope is two channel, connect the second channel to terminal 5 of TA1.