FURUNO 1832 PDF

Furuno 36 mile CRT 4kW radar with 24″ radome. I would be interested in his Furuno radar – any-one got any experience with this particular bit of equipement? What’s it like – features, easy. Furuno Pdf User Manuals. View online or download Furuno Operator’s Manual.

Author: Yorisar Nir
Country: Armenia
Language: English (Spanish)
Genre: Automotive
Published (Last): 3 May 2010
Pages: 262
PDF File Size: 17.79 Mb
ePub File Size: 16.84 Mb
ISBN: 302-9-46462-486-8
Downloads: 64441
Price: Free* [*Free Regsitration Required]
Uploader: Gulabar

Printed in Japan Pub. To see if your product has a battery iessee the chapter on Maintenance.

Follow the instructions below if a battery ies is used. Features Your radar has a large variety of functions, all contained in a remarkably small cabinet. Within 20 of mainlobe; less than dB Outside 20 of mainlobe; less than dB 6. Range, Range interval and no. Calculated value based Magnetic variation. Although the basic principles of radar were developed dur- ing World War II, echoes as an aid to naviga- tion is not a new development.

Displays the data of target selected with the cursor. Terminates plotting of the target selected with the cursor. Temporarily erases heading line and north ffuruno if displayed. The control panel furyno and a timer displays the time remaining for warm up of the magne- tron the device which produces radar pulsescounting down from 1: Availability of fuuruno particular display item depends on incoming data.

When Range to Waypoint reaches 0. When cross track error exceeds 1 nm on either side, the XTE mark starts blinking.

If the control is set too low, targets will be hid- den in the clutter, while if it is set too high, both sea clutter and targets will disappear from the display.

By cursor Operate the omnipad to bisect the target with the cursor intersection. The bearing to the tar- get appears at the bottom of fueuno display. Guruno location with the cursor. To open or close the menu, press the [MENU] key.

Furuno 1832 User Manual

You can select items on the menu with the omnipad. The complete menu appears on page AP True motion True motion displays own ship and moving objects in their true motion.

Continuous trail The maximum continuous trail time is 99 min- utes and 59 seconds. When the elapsed time clock counts up to that time the elapsed time display is reset to zero and trail begins again. Select level desired by operating the omnipad. Press the [MENU] key to close the menu. IR and level selected appears at the bottom right corner on the display when the interfer- ence rejection circuit is turned on.

  HIOKI 3454-11 PDF

Furuno User Manual – Page 1 of 63 |

Asterisk blinking Guard zone to set Drag cursor here. Figure How to set the guard zone Silencing the audible alarm Any radar targets violating the guard zone will trigger the audible alarm. Panel Dimmer Select level of panel backlight. HD Mark Select brilliance of heading mark. The function can be turned off by pressing appropriate function key again.

Shift brief press or Zoom long press F2: Ring brillience How to register menu items 1. In some cases the effects can be reduced or eliminated. The operator should familiarize himself or her- self with the appearance and effects of these false echoes, so as not to confuse them with echoes from legitimate contacts.

Direct path Target Indirect path Obstruction mast, funnel. Before reviewing this chapter please read the safety information which follows. Hazardous voltages can shock, burn or cause death. If you cannot restore normal operation, do not attempt to check inside any unit of the radar system.

Any repair work is best left to a qualified technician. Table Life expectancy of magnetrons Model Type Code no.

Radome cover Figure Antenna unit Mounting platform Holes for antenna unit: The mounting surface must be parallel with the waterline and provided with five holes whose dimensions are shown in the outline drawing attached at the end of this manual. The unit is adjusted so a target echo returned from the bow direction will be shown on the zero degree heading line position on the Remove the cable clamping plate by un-fastening four screws and removing a gasket.

Screws Shield cover Screws 7 pcs. Shield cover Screws 7 pcs. Shield cover Figure Antenna unit, inside view 7. Pass the cable through the hole at the bottom of the radome base. Detach the antenna housing cover from the antenna housing by loosening four fixing bolts.

FURUNO 1832 Radar Marine GPS

The antenna housing cover fitted with the transceiver module can be stored in a convenient place until the wiring to the an- tenna unit is done. Apply grease to the O-ring and set it to the center of the radiator bracket. Coat the ra- diator fixing bolts with silicone sealant. Signal cable connector DJ-1, waterproof Left: Temp Unit Magnet 4.

Key Beep Rotate 6. As a final test, move the boat towards a small buoy and confirm that the buoy shows up dead ahead on the radar when it is visually dead ahead. Adjusting sweep timing Adjustment range: Setting a blanking area When the antenna is installed at a close dis- tance in front of the wheelhouse, the radar should be set not to transmit within that area.

  HARRY POTTER EL PRINCIPE MESTIZO PDF

No echoes appear in the blanking areas.

Keep magnets and magnetic fields away from the equipment. Magnetic fields will distort the picture and can cause equipment malfunction. The Auto Plotter permits manual or automatic acquisition and automatic tracking of up to 10 radar targets. Activating the Auto plotter To activate the Auto Plotter, follow the steps shown below: Press the [MENU] key to open the main menu.

Operate the omnipad to select the “1. Operate the omnipad to select “Off”. Acquiring fueuno Manual Acquisition Follow the steps below to manually acquire a Figure AP-4 Auto acquisition area Follow the steps shown below to activate the auto acquisition fyruno 1. Auto ACQ” by operating the omnipad. Operate the omnipad to select “On”. The flashing of the triangle plot symbol and vector remain on the screen until the danger- ous situation furjno no longer present or you in- tentionally terminate tracking of the target by Also See for Operator’s manual – 62 pages.

Page of 64 Go. Table of Contents Add to my manuals Add. Marine Radar Furuno Quick Manual Summary of Contents for Furuno Page 2: Principle Of Operation 1. Display Indications And Markers 2. Selecting The Range Note 1: Measuring The Bearing 2. Shifting off Centering The Picture 6. Magnifying Long Range Echoes echo Stretch True motion True motion displays own ship and 183 objects in their true motion.

Suppressing Radar Interference Continuous trail The maximum continuous trail time is 99 min- utes and 59 seconds. Watchman Asterisk blinking Guard zone to set Drag cursor here.

Other Menu Description 3. Page 43 Apply grease to the O-ring and set it to the center of the radiator bracket. Display Unit Installation Code no. Adjusting Sweep Timing 5. Magnetron Heater Voltage Setting a blanking area When the antenna furuni installed at a close dis- tance in front of the wheelhouse, the radar should be set not to transmit within that area.

Page 50 This page is intentionally left blank. Page 56 Figure AP-4 Auto acquisition area Follow the steps shown below to activate the auto acquisition area; 1.

This manual also for: Comments to this Furuo Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it.