CatEye CC-VL/CC-VL [Velo 5/Velo 8] manuals and user guides for free. Read online or download in PDF without registration. Recent Cat Eye Velo 8 questions, problems & answers. Free expert DIY http:// % I have recently received a CatEye Velo 8 as a gift. After the Enter the number into the computer as per the instructions. When under pressure.
|Published (Last):||21 August 2013|
|PDF File Size:||17.66 Mb|
|ePub File Size:||2.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
Cycling Posted on Nov 04, Be the first to answer. The distance between the sensor 3 and the magnet 4 must be less than 5mm. The cadence function stopped working.
Operation flow setting, Battery, 9691n – CatEye CC-VL510/CC-VL810 [Velo 5/Velo 8] User Manual
No measurement is done on the VELO5. If unsure take the bicycle to a bicycle shop to have new ones fitted. However, the Odometer total distance and Clock do not return to zero.
Current speed does not appear.
20 Most Recent Cat Eye Velo 8 Questions & Answers – Fixya
The unit starts measuring automatically when you start pedaling, and stops measuring when your come to a stop. Unless it’s the wire and you can fix it you need to buy a new computer. When it comes to Fixiesit has no mechanism on the hub. Each time you press the MODE button, a different data value appears on the lower line.
Please assign your manual to a product: When rotating the front wheel, the magnet’s 4 center must be aligned with the sensor’s 3 marking line.
Recent Popular Answered Unanswered. If mph has been selected, it becomes hour clock. If you are not a professional athlete then the number of gears you catey does not really matter.
Wipe any water or dirt from the contacts and apply a water repellent silicon grease. I installed a fresh battery, I adjusted the sensor location. If current speed appears, gelo main unit is working fine and the cause should be attributed to the bracket or the sensor.
CatEye CC-VL User Manual | 2 pages | Also for: CC-VL, CC-VL/CC-VL [Velo 5/Velo 8]
If the main unit does not receive a signal after about 10 minutes, the main unit enters Power Saving Mode and displays the clock count only. This manual is related to the following products: Indicates the mode currently selected. Microcomputer 4-bit 1-chip Crystal controlled oscillator Display Liquid crystal display Sensor No-contact magnetic sensor Tire Sizes Tire sizes of 16, 18, 20, 22, 24, 26, C, and 27 inches, or tire peripheral lengths from to cm Initial value: B The distance between the sensor 3 and the magnet 4 must be less than 5mm.
Clean the contact with a cloth. It all manuwl down to the rear hub and how the single cog is connected to the rest of the drivetrain. Is the cord broken? Replace the bracket and sensor set with a new one. The upper display always shows the Current Speed. The corresponding value is indicated on the lower line. Do all clear operation. You need low enough gears for going up hills and high enough gears for inclines. Cycling Answered on Nov 22, The clearance should be less than 5mm. Correct positions of the sensor and the magnet: Always be sure to ride safety.
But Most people don’t know the difference between a fixie and a single speed bike. Cycling Answered on Nov 02, The cog is fixed veelo the careye.
Re-adjust the positions of the magnet and the sensor. Single speed bikes are often known as Fixed gear or fixie bikes.
CatEye CC-VL800 User Manual
You can measure the outside diameter of your current seat post with a metric ruler or measure the inside of the hole of the frame. Gtanite peaks bicycle Cycling Posted on Dec 27, Be the first to answer.
Loosen it and you should be able to raise the bar an inch or 2. First, short-circuit the contact of the main unit a few times with a piece of metal. Microcomputer 4-bit 1-chip Crystal controlled oscillator Display Liquid crystal display Sensor No-contact magnetic sensor Tire Sizes Tire sizes of 16, 18, 20, 22, 24, 26, C, and 27 inches, or tire peripheral lengths from to Either select from among preset sizes.
Cat Eye Cycling Answered on Aug 17, Is there anything sticking on the contact of the main unit or the bracket? A When rotating the front wheel, the magnet’s 4 center must be aligned with the sensor’s 3 marking line. Andrew Taylor Level 3 Expert Answers. Do not apply standard grease, as it may cause damage to the bracket.
Ask a Question Usually answered in minutes! Cycling Answered on Dec 26, Cat Eye Enduro 2 -1 Questions.
Single speeds are fitted with a freewheel cog that rotates freely one way but locks up the other.