ANILAM 1100M PDF

I have an anilam that quit working. Will the drive motors from the anilam work with a mach 3 system. And where does a person find a. Hello, Out Anilam m 2 axis system is giving us no video and the computer will not boot. Does anyone know how to repair the system?. Anilam is the company that makes the control. I run a Sharp knee mill with a Aniliam M control. I’m not familiar with the M or sure what.

Author: Mazujinn Tosho
Country: Fiji
Language: English (Spanish)
Genre: Video
Published (Last): 9 November 2008
Pages: 165
PDF File Size: 3.52 Mb
ePub File Size: 15.65 Mb
ISBN: 947-7-99997-830-4
Downloads: 91898
Price: Free* [*Free Regsitration Required]
Uploader: Kazrami

Circle Adjusted beyond Maximum adjustment: Remove the cable on the PC board labeled P3. The following drawing is the servo turn on circuit: This is going to erase memory and clear your problem.

If any of the voltages are wrong please order part from Anilam or from your local Distributor. Once we have found the bad item that will either be the motor or the motor cable or both, continue checking the remaining axis the same way. The anilm drawing is for 3 axis Motion board part s.

Make sure line 1 which says Execution Mode is set for buffered not drip feed. It can also convert an existing G-code program to Anilam. Press the F10 key.

If the light is on, is it illuminated on all of the drive cards? This message means the control sent a signal out of the motion board but did not see any counts coming back in. If it does you need to order a new motion board.

  DANFOSS VLT 6011 PDF

Using the down arrow key Highlight the Miscellaneous choice and press the Enter key. Adjust until you obtain 5. The arc is usually split in to 11100m arc statements. No counting on all axis. Go to the program page by pressing the F2 key.

If the switch was Anikam you have a bad motion control board. After the computer boots from the diagnostic disk, select F1 key in order to run the software.

Anilam 1100M Programming Manual CNC Three Axis

Using the down arrow key Highlight General Software and press the Enter key. Highlight Copy and press the Enter key. After connecting this cable turn back on the power and recheck your system to see if you are still loosing zero. Are you loosing zero after the servo shuts down?

Controller & Computer Solutions > Anilam m software

Please locate this number and write it down. Since this is my first dance, I am cautious.

Turn the VAC power anilwm on and leave the servo box door open. Go to Machine Axis and press the Enter Key. Hi JT; It is conversational anulam it says it can be toggled over to g-code. Make sure all the buttons work, for that matter.

Contact Anilam or your local Distributor to get the defective part replaced. Thanks Do you know what they mean by conversational control?

DNC configuration suggestions are as follows. Similar Threads Anilam t Offline software, anyone have it? I’m going to look at it under power in a couple of days with cash in hand and a trailer on the back of my truck. On the one hand, they are there when you need them, and on the other hand, they want to sell you expensive repair parts that you can’t get anywhere else. If swapping the motor the problem moved to the other axis, then the problem is in snilam encoder which is built into the motor.

  GEORGE ELDON LADD TEOLOGIA DO NOVO TESTAMENTO PDF

I am having a real tough time trying to hunt and peck my way anllam this control. On some of the original distribution board systems check to see if you have R43 and R44 still mounted on the distribution board.

Anilam M Programming Manual CNC Three Axis pdf – CNC Manual

Schematic of PC Please either repair the wire trace or order a new PC board. If you can’t find it just send me a PM and I will respond when I get home. It is only a problem with the computer, the servos, drives, power supply, and everything else is fine. It was my attempt to preclude my query being one of those, which people look at. The following drawing is the DSP Board part s. If the problem persists please contact your local Anilam distributor or Anilam directly.

This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy. Results 1 to 7 of 7. M function Option not available: Please read the following document which explains the proper procedure to discharge static electricity.